Competitive Rollout for Ardent
3 posters
:: Club Racing :: Ardent Raceway
Page 1 of 1
Competitive Rollout for Ardent
Hi Guy's
I ran my first GT-10 car in round 1 of the BRCA national the other week and finished last in the C final.
I drove pretty clean and the car seemed very stable but I was way off the pace. Any advise on a good starting point rollout wise and any other general advise would be great. I intend to enter in to this series as well and join in the fun !!
Bit of info on set-up CRC Gen-x10, Novak GTB, Speedpassion 10.5. I run 48dp.
I ran my first GT-10 car in round 1 of the BRCA national the other week and finished last in the C final.
I drove pretty clean and the car seemed very stable but I was way off the pace. Any advise on a good starting point rollout wise and any other general advise would be great. I intend to enter in to this series as well and join in the fun !!
Bit of info on set-up CRC Gen-x10, Novak GTB, Speedpassion 10.5. I run 48dp.
Don1- Posts : 10
Join date : 2011-05-14
Location : Leeds West Yorkshire
Re: Competitive Rollout for Ardent
post your rear foam diameter in mm so a rollout can be worked out
in the meantime download this spreadsheet
[You must be registered and logged in to see this link.]
which SpeedPassion 10.5 sport or race motor?
in the meantime download this spreadsheet
[You must be registered and logged in to see this link.]
which SpeedPassion 10.5 sport or race motor?
Re: Competitive Rollout for Ardent
chequered_flag_racing wrote:post your rear foam diameter in mm so a rollout can be worked out
in the meantime download this spreadsheet
[You must be registered and logged in to see this link.]
which SpeedPassion 10.5 sport or race motor?
Hi, Rears are 56mm diameter motor is the SpeedPassion 10.5 Sport.
Thanks for the response
Don.
Don1- Posts : 10
Join date : 2011-05-14
Location : Leeds West Yorkshire
Re: Competitive Rollout for Ardent
should have asked what size spur your using
don't need the pinion as this is chosen to suit mmpr
which pinions did you try at Ardent?
save the spreadsheet and then change the foam diameter in the green boxes to suit your foams
don't need the pinion as this is chosen to suit mmpr
which pinions did you try at Ardent?
save the spreadsheet and then change the foam diameter in the green boxes to suit your foams
Re: Competitive Rollout for Ardent
On the day I had a 70 Spur and 24 pinion and the tyres were 60mm but since I have dropped the tyres to 56mm. I have several spurs from 70 up to 78 to try.
Don1- Posts : 10
Join date : 2011-05-14
Location : Leeds West Yorkshire
Re: Competitive Rollout for Ardent
OK so reading over thread again your esc is holding you back in terms of speed. Most if not all the cars in the top 20 will have been running an esc with TOTF (Timing On The Fly) built available. Tekin's, Hobbywing 1s to name but two.
rollouts
Ardent on 60mm rears = 24/70 & 60mm = 64.63mmpr
56mm rears = 24/70 & 56mm = 60.32mmpr
to get back to similar Ardent mmpr you need 27/74 & 56mm = 64.19mmpr
rollouts
Ardent on 60mm rears = 24/70 & 60mm = 64.63mmpr
56mm rears = 24/70 & 56mm = 60.32mmpr
to get back to similar Ardent mmpr you need 27/74 & 56mm = 64.19mmpr
Re: Competitive Rollout for Ardent
Many thanks for the info, I'll check out the speedo's.
Is 64 mmpr about right then or should I be looking at a bit higher?
Is 64 mmpr about right then or should I be looking at a bit higher?
Don1- Posts : 10
Join date : 2011-05-14
Location : Leeds West Yorkshire
Re: Competitive Rollout for Ardent
depends on the motor and speedo.
I ran a tekin rs pro and tekin 10.5 motor boosted with a 52mm roll out at ardent. Went down to 48mm at chesterfield and it was great so will see how it goes at ardent.
I ran a tekin rs pro and tekin 10.5 motor boosted with a 52mm roll out at ardent. Went down to 48mm at chesterfield and it was great so will see how it goes at ardent.
chris_blakey- Posts : 20
Join date : 2011-03-15
Re: Competitive Rollout for Ardent
Thanks again for your help, some track time needed for me and some investment in a new ESC.
Cheers
Cheers
Don1- Posts : 10
Join date : 2011-05-14
Location : Leeds West Yorkshire
Re: Competitive Rollout for Ardent
Don1 wrote:Thanks again for your help, some track time needed for me and some investment in a new ESC.
Cheers
Hobbywing XERUN-120A-1S ESC is worth a punt
Similar topics
» Ardent brushless rollout
» Ardent RND 4
» Ardent Sun 6th
» F1 at ardent 30/01/11
» How to get to Ardent
» Ardent RND 4
» Ardent Sun 6th
» F1 at ardent 30/01/11
» How to get to Ardent
:: Club Racing :: Ardent Raceway
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|